PMCC Closed Cup Flash Point Tester For Petroleum Testing
 PMCC Closed Cup Flash Point Tester For Petroleum Testing This instrument is designed and manufactured as per standards GB/T 261-2008 Determination of Flash Point – Pensky-Martens Closed Cup Method and ASTM D93 Standard Test Method for Flash Point by Pensky-Martens Closed Cup Tester. It is used to make determination of the closed cup flash point of the petroleum products.
- Description
- Inquiry
Introduction
Laboratory Used PMCC Closed Cup Flash Point Tester For Petroleum Testing This instrument is designed and manufactured as per standards GB/T 261-2008 Determination of Flash Point – Pensky-Martens Closed Cup Method and ASTM D93 Standard Test Method for Flash Point by Pensky-Martens Closed Cup Tester. It is used to make determination of the closed cup flash point of the petroleum products.
Features
1. This instrument is designed as per GB/T261 and ASTM D93.
2. The heating power is continuously adjustable. The power is shown visually by voltmeter.The temperature control mode is advanced and reasonable.
3. The structure is designed small and exquisite.The stainless-steel table board is beautiful and easy to clean.
4. Operation is easy.Test results are precise.It has been chosen as the instrument to test the closed cup flash point by many metering and detecting institutes.
Â
Parameter
Power supply:AC (220±10%)V, 50Hz;
Total power consumption:≤650W;
Heating device: Â Â (1)The furnace body is made of silicon carbide
                  (2)Heating power is adjustable from (0-600) w.       Â
Heating mode: Adjust by manual.
Stir mode: Mechanical drive stirring.
Stirring rate: Procedure A: (90~120)RPM, Procedure B: (250±10)RPM
Oil cup:(1) Inner diameter: 50.7mm~50.8mm.
          (2) Depth: 55.7mm~56.0mm
          (3) The scribed line depth of capacity of testing oil: 33.9mm~34.3mm.
          (4) Capacity of testing oil:about 70ml
Igniting source: gas(or other civilian fuels,the same below)
Thermometers:Mercury-in-glass thermometer.Specifications are as below:
                (1)Scale -5℃~110℃, division 0.5℃.
                (2)Scale 20℃~150℃, division 1℃.
                (3)Scale 90℃~370℃,division 2℃.
Ambient temperature:(15~35)℃
Relative humidity:≤ 85%
Dimension: 370mm×320mm×300mm
Net weight: 7kg
Â
Related Products
Asphalt Bitumen Non-nuclear Electronic Density Gauge (EDG)
The EDG-2A non-nuclear asphalt density tester can quickly detect areas where road surface segregation, low density, and unevenness occur. The use of electromagnetic induction technology instead of nuclear source radiation method, low cost, high security, users do not have to worry about cumbersome environmental assessment applications, time-consuming training, and strict transportation control. The calibration is simple, the precision is high, the repeatability is good, the touch screen operation, the user can complete the relevant operation training in a short time, and master the technology of on-site quality inspection.
Coating Adhesion Bonding Strength Tester
Coating Adhesion Bonding Strength Tester is a new type of instrument, which is mainly used in the detection of coating adhesion in the construction of high-speed rail projects. It is a necessary testing instrument for quality inspection and construction units.
Los Angeles Fragmentation Abrasion Machine
ASTM Standard Digital Display Los Angeles Fragmentation Abrasion Machine is for measuring aggregate toughness and abrasion resistance, crushing, degradation an disintegration.
AC DC Magnetic Particle Yoke Flaw Detector
AC DC Magnetic Particle Yoke Flaw Detector has AC, DC, AC and DC dual-purpose magnetic particle flaw detector. The DC power supply is rechargeable battery, which is suitable for field operation without power supply and high-voltage inaccessible containers, bridges, pipelines and other field operations. The continuous working time of one charging can reach more than 6 hours. The AC power supply adopts ~ 220 V power supply for direct input without other instruments. It is easy to operate, simple, light weight and easy to carry.
Multifunction Pull Off Bond Strength Tester
40 kN Multifunction Pull Off Bond Strength Tester For Concrete Testing It is mainly used to detect the strength of concrete after installation and pull out, and to inspect the bonding strength of concrete facing bricks, mosaics, and wall or ground and the strength of concrete, chemical anchor drawing test.
This instrument is a small hydraulic force-measuring device. When testing the adhesive strength of decorative bricks, the three-point counterforce support is used to generate tensile force on the adhesive material of decorative bricks. The concrete is tested by using the principle of post-installation and extraction. The force required to anchor the concrete in the concrete is used to calculate the strength of the concrete.
The instrument consists of a through-hearth jack, a hand pump, a triangular chassis, and a force measuring device. It has the characteristics of one machine and two uses, a novel structure, small size, convenient operation and complete functions.Concrete Steel Bar Rebar Location and Corrosion Detector
Concrete Steel Bar Rebar Location and Corrosion Detector Integrate the functions of rebar position test , concrete thickness test, rebar diameter test and rebar corrosion degree test into one product.
Penetration Mortar Concrete Compressive Strength Tester
Handle Penetration Mortar Concrete Compressive Strength Tester is suitable for masonry mortar strength testing and concrete strength testing. A new type of on-site detection method that uses the lever-type baster force method to penetrate the nail into the mortar and converts the compressive strength of the mortar through the penetration depth of the nail and the strength curve.
Concrete Rebar Scanner
Portable Integrated Concrete Rebar Scanner Concrete Locator Concrete Rebar Detector For Concrete Cover Meter are mainly used for detecting the internal reinforcement position, the protective layer thickness, reinforcement spacing and diameter of rebar.
Concrete Resistivity Tester
Concrete resistivity tester is also called potential detector. The corrosion of steel bar/ reinforcement in concrete is an electrochemical process, it creates an electric current to make metal dissociation. The lower the resistivity, the easier corrosion current flowing through the concrete, and the greater the likelihood of corrosion. So measuring the resistivity of concrete can effectively evaluate its ability to resist corrosion and evaluate existing steel corrosion degree.
Pocket Rebar Detector Steel Bar Detector Scanner
LCD display Handheld Pocket Rebar Detector Steel Bar Detector Scanneruses an electromagnetic induction method, which can detect the rebar location and cover thickness & diameter accurately, store, transfer and analyze the real time test data. The model is the pinnacle of work with the modern simple design, incorporating the handy & durable features and sophisticated electronic technology.
Rebar detector is mainly used to test the location, distribution, direction, the thickness of rebar and the diameter of cover in concrete structure such as walls,columns, beam-slabs etc. It can also detect the location of pipelines and metal embedded parts. The multiple coil structure design make it more accurate&responsive and higher resolution.
